Article Display Header Ad Mobile



No announcement yet.

Advanced Subwoofer Techniques


  • Advanced Subwoofer Techniques

    There are a few tricks you can pull out of your sleeve to make your low frequency arrays work better. By building directional subwoofer arrays, energy can be kept off the stage and walls and kept on the audience where it belongs. These arrays require a little more signal processing and planning to implement, but the reward can be as much as 20dB less energy where it isn’t wanted. I’m going to demonstrate how to implement these arrays yourself with any collection of identical front-loaded subwoofers.

    We’re going to explore two kinds of arrays, cardioid and end-fire, both of which create wideband rejection to the rear and sides of the array. The name “cardioid” means the same thing as it does for directional microphones: the polar response of the array has a heart-shaped pattern. While we are technically describing a desired pattern shape rather than a specific type of array, it has become common in the live sound industry to describe this first type of subwoofer array as “cardioid.” An end-fire array is so named because a number of subwoofers are arranged in a line and delayed so that they “fire” in order, beginning at the end furthest from the audience.

    Cardioid Array
    A cardioid array (Figure 1) uses a mixture of polarity and delay to create directionality. The technique requires two sources physically separated relative to the desired direction of cancellation. Placing three subwoofers next to each other but flipping the middle one so it faces backwards can easily achieve this. Delay is then applied to the rear-facing subwoofer to time align all loudspeakers towards the rear. Inverting the polarity of the rear-facing subwoofer then creates cancellation as the energy from the front-facing subwoofers arrives only to be met by the inverse energy radiated by the rear-facing subwoofer, which nullifies it. This is certainly non-intuitive behavior, using sound to cancel sound, but it works!

    Click image for larger version

Name:	Figure-1web.jpg
Views:	1
Size:	32.5 KB
ID:	194292

    Figure 1
    Meanwhile, in the forward direction we have created a large time misalignment by not only separating these sound sources, but also delaying one so it appears even further away. If we choose the distance between front- and rear-facing sources carefully, we can make this misalignment work in our favor once again. At a certain frequency, the energy from the rear-facing driver arrives at the front of the array one-half wavelength (180°) out of phase. Ordinarily this would create cancellation, but remember that we inverted the polarity of the rear-facing subwoofer. What was 180° of phase difference is now 0° and cancellation becomes addition in front, just as addition became cancellation to the rear courtesy of the same polarity inversion.
    The physical distance between drivers defines one quarter-wavelength of this frequency, while the alignment delay defines the other quarter-wavelength. A spacing of 2.5’, for example, will provide near-perfect addition towards the audience at approximately 110Hz. However, as frequency changes so does wavelength. Keep in mind that an octave above or below this frequency (55Hz and 220Hz, respectively) there will be 90° of phase difference relative to the center frequency, which results in less contribution from the rear-facing subwoofer. In practice subwoofers rarely operate over two or more octaves bandwidth, so this is usually not an issue. Since the cancellation to the rear is provided by polarity inversion it is equally effective at all frequencies.

    Determining the delay to apply to the rear-facing subwoofer is not intuitive, since the cabinet depth alone is not an accurate representation of how long it takes the energy from the front-facing drivers to reach the rear-facing driver. The correct delay can be determined by taking a tape measure and measuring the shortest distance from the center of one driver around one side of the cabinet to the center of the other. This represents the actual path the sound must take and therefore the actual delay. For the sake of simplicity, however, one can usually get a perfectly functional approximation by taking the cabinet depth and multiplying by two. To convert from distance to delay, remember that sound travels approximately one foot every 0.9ms.

    The reason I have been using three cabinets throughout this example is that most subwoofers are slightly directional due to their size, so the energy arriving at the rear of the array is already down 2-3dB. For ideal cancellation we would therefore need to turn down the input to the rear-facing cabinet by an identical amount. I prefer to simply use three cabinets, two facing forward and one facing backwards, which elegantly accounts for the level difference. The same setup works using subwoofers stacked three high with the bottom one reversed, as in Figure 2. This can get you a lot of output and directivity from a very small footprint, if height is not a concern.

    Click image for larger version

Name:	Figure-2web.jpg
Views:	2
Size:	24.6 KB
ID:	194296

    Figure 2
    End-Fire Array
    The second basic type of directional array is an end-fire array (Figure 3), which operates more like a shotgun microphone. The basic mechanism is to line up a number of subwoofers in the direction of the audience, and then delay each forward subwoofer back to the rearmost. As the energy travels down this line of subwoofers each contributes in time, creating forward addition. Simultaneously, rearward energy becomes a jumble of mixed time arrivals, which tend to cancel each other out. As loudspeakers are added to the array, the rejection to the rear and sides increases along with the output towards the audience.

    Click image for larger version

Name:	Figure-3web.jpg
Views:	1
Size:	34.7 KB
ID:	194289

    Figure 3
    To build an end-fire array you’re going to need a number of identical subwoofers and a few channels of digital delay. Build a line of subwoofers spaced an equal distance apart (I find as little as 4” of separation to work very well). The subwoofer furthest from the audience will be time zero, so for every subwoofer closer to the audience add delay equivalent to the distance between it and the furthest.

    There is more a practical than a theoretical limit to the length of the line, and very deep arrays may cause more rejection to the sides than is actually desired, so it may be helpful to determine ahead of time what kind of pattern you require. For an extreme example, Figure 4 shows an 8 element deep end-fire array at 60Hz. There are some lobes to the side of the array, but the forward behavior remains excellent while the rearward rejection is tremendous. I find 3-4 subwoofers deep to be a reasonable compromise between rejection, size, and complexity for these arrays.

    Click image for larger version

Name:	Figure 4.png
Views:	1
Size:	77.9 KB
ID:	194291

    Figure 4
    Pros and Cons
    Both methods create rejection, the important question is where and at what frequency? Cardioid arrays tend to have a very stable pattern because of their use of polarity inversion. They can also often be built within the same footprint as a traditional array. Furthermore, by slightly varying the delay for the rear subwoofer it is possible to narrow or widen the pattern in order to fit your exact application. The price you pay with a cardioid array is reduced output as frequency drops; since one subwoofer is polarity inverted, as the wavelengths get longer both subwoofers begin to behave like a single source and cancel in all directions. In practice this reduction in output is not critical as long as the array is built with a reasonable center frequency in mind.

    End-fire arrays have their own set of compromises. Their primary advantage is near-perfect addition in the forward direction. Their primary disadvantage is the physical space required to implement them. Additionally, as subwoofers are added to the line more separate delay taps are required, which may require more amplifier or processor channels than are available. Most importantly, an end-fire array depends entirely on phase interaction to create rejection and therefore has a different pattern at every frequency, as the wavelengths involved are different at every frequency. This can create uneven frequency response off-axis, which exacerbates the issue of where in the audience area to equalize the PA.

    Application Primer
    Once you’ve built a few directional arrays you’re naturally going to want to integrate them into a larger system. This is where acoustic modeling software comes in very handy, since in some cases arrays of directional subwoofers don’t behave like arrays of conventional subwoofers. Especially when integrating traditional and cardioid arrays, extra care must be taken to verify that the results are as expected. We all have a lot of experience working with subwoofers that radiate omni-directionally, it can be frustrating to put together an array only to find it does not behave the way you thought.

    For an example of unexpected but beneficial behavior, imagine that we are in a venue that has a very wide audience area. Traditional left and right stacked subwoofers (Figure 5) provide inadequate coverage: too much bass down the middle and to the extreme sides relative to the majority of the audience area. By substituting end-fire arrays at 45-degree angles (Figure 6), coverage is dramatically improved for all but those just off center! Where audience members to the sides were hearing both subwoofer arrays but at different times, now where one array is the loudest the other has significant rejection, reducing interaction and improving coverage… especially 45-degrees off axis where before there was no energy at all. This works just as well with cardioid arrays, of course!

    Click image for larger version

Name:	Figure 5.png
Views:	1
Size:	86.7 KB
ID:	194293

    Figure 5
    Click image for larger version

Name:	Figure 6.png
Views:	1
Size:	84.0 KB
ID:	194290

    Figure 6
    All of these arrays can be used to create a low frequency system that provides very even coverage over large or small audience areas, with the added possibility of keeping a lot of that arena-rattling bass off your stage and out of your microphones. It is important to recall that the subwoofer system is but one component of a series of systems all working in concert to create even energy over your audience area. Just because you have a flawlessly designed and deployed low frequency system doesn’t mean that it will operate the same when integrated with other acoustic sources.

    Critically important, and notably left out from other subwoofer articles I have read, is how the subwoofer and main PA arrays behave together. At 30Hz this is not a concern, but up near the crossover frequency it can be a serious problem. Consider that, at the acoustic crossover frequency, by definition the mains and subs are producing equal level. This means that in the crossover region the mains act as a subwoofer system all to themselves! In short, your formerly perfect subwoofer system is now compromised by left- & right-stacked subs anyway, in the form of the main loudspeakers (Figure 7)!

    Click image for larger version

Name:	Figure 7.png
Views:	1
Size:	70.4 KB
ID:	194294

    Figure 7
    Unfortunately, discussing that issue, and the many others that arise with system integration, could take another 100 pages. Some solutions I have employed include utilizing both center clustered and left/right subs, or deploying a very wide center sub array (i.e. the width of the stage and/or venue). In this case there is not one definitive answer, but another excellent reason to get your hands on some acoustic modeling software and play around. Not all software will work below 100Hz, but there are several that will and many of them are also free (see the end of this article). I highly recommend modeling first using realistic numbers of enclosures and distances whenever you consider deploying advanced subwoofer arrays.

    Hopefully between this article and my last one (Run and Gun Subs, November 2010) you have achieved a newfound understanding of the disadvantages of conventional left/right subwoofer arrays and the many options available to you. With a little knowledge of phase and some spare DSP it is possible to mold low frequency energy to your whims. Reducing energy on stage can take strain off your monitor systems and your crew while cleaning up sound for the audience. The same arrays that create that rejection can also reduce interaction in the audience area and create an overall superior tonal balance from front to back and side to side. By spending a little time on a computer before the gig you can determine exactly what is possible with the resources available to you and have a sound system that is the envy of every other speaker-phile in the area.

    Click image for larger version

Name:	Extra-1web.jpg
Views:	2
Size:	69.9 KB
ID:	194295

    An end-fire array.
    The incredibly-shirted person in the background is the author.
    This article would not have been possible without the use of images generated by G.P.A. 2.2, freeware acoustic modeling software by Sebastian Rivas Godoy. His website may be found at

    • Tim McCulloch
      Tim McCulloch commented
      Editing a comment
      Your shirt is louder than the sub array, and it's unfortunately an omni. I also note a serious "hands in pockets" thing...

      For Valentines Day we had a radio show with 3 acoustic acts and 2 full bands. In this small arena (6500 cap) we've had the usual issues of power alley taking over the middle of the deck, and the acoustic performers have been uncomfortable with getting their dental work shaken.

      I deployed 6 JBL VerTec 4880 per side in a cardioid-pattern array... FRFFRF (front, rear, etc). The rear-facing speakers were polarity-reversed and delayed. The cancellation was on the order of 9 db or more (based on my highly calibrated "ear measurements") and the acoustic performers were very happy with the results. The BEs were very happy with the more uniform coverage of the listening area as well and there was praise for the system implementation and alignment.

      For anyone with LF coverage issues, experiment with the techniques in Bennett's articles. Try them outside or in a large room to help reduce the impact of reflections.

      Have fun, good luck.

      Tim Mc
      Last edited by Tim McCulloch; 02-15-2011, 07:04 PM. Reason: Fixed stuff...

    • Jared Koopman
      Jared Koopman commented
      Editing a comment
      I will preface my question with this..I have absolutely no experience working with rigs of this size.

      My question is:
      Are end fire arrays used in install setups or is this technique used primarily for touring setups? For example would a church or theater implement this setup? Is it possible to use an end fire array installed under a stage to minimize visual impact and space, or does the end fire array require "space" to function properly? Al lthe photos that I have seen of this type of setup shows it out front or on the sides of a stage. Is that purely a function of not having space under the stage or is there a sonic benefit as well?

      I apologize if this is a dumb question, just trying to learn and understand.

      Thanks for your time,
    Registration is required to post comments.

Latest Discussions