Log in
Register
Home
Forums
New posts
Search forums
What's new
New posts
New profile posts
Latest activity
News
Members
Current visitors
New profile posts
Search profile posts
Features
Log in
Register
Search
Search titles only
By:
Search titles only
By:
New posts
Search forums
Menu
Install the app
Install
Reply to thread
Home
Forums
Pro Audio
Junior Varsity
iNuke nu3000DSP outputs when in bridged mode
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Message
<blockquote data-quote="Mitch Miller" data-source="post: 141171" data-attributes="member: 2673"><p>Re: iNuke nu3000DSP outputs when in bridged mode</p><p></p><p></p><p>That's pretty much what I expected. </p><p></p><p></p><p>This I didn't know. Thanks. </p><p></p><p></p><p></p><p>Didn't know it was 28Hz on those boys (thanks for that). Saw that spec. on some others (while trying to find specs. on the Sigma 18 Pros), but didn't make the correlation to why that's important. but that totally makes sense. And here I was just trying to prevent low-end sub-sonic rumble from overheating the voicecoils.</p><p></p><p>Incidentally, that's the second time today I saw video of that bridge -- someone is trying to crowd-fund a propless wind powered electric generator and used the same event as part of their promo piece.</p><p></p><p>Much appreciated.</p><p></p><p>So, since the amp has the DSP, and it's not as easy to accidentally change, and that amp will be sticking with these subs for a while, I think I'll move the HPF over to the amp instead of the board. Kinda less chance of accidentally changing (or removing altogether).</p><p></p><p>Still a little uncertain where'd be a good level for the power limiter. I currently have it set to 1200 watts (as I understand, it has only a peak limiter), which is likely a little hot for those drivers. And I suppose, if I bring it down to under 880 (2x440), then I might as well unbridge the thing and not have to worry about special cables, etc. (since each side can deliver 440 watts max into 8 ohms).</p></blockquote><p></p>
[QUOTE="Mitch Miller, post: 141171, member: 2673"] Re: iNuke nu3000DSP outputs when in bridged mode That's pretty much what I expected. This I didn't know. Thanks. Didn't know it was 28Hz on those boys (thanks for that). Saw that spec. on some others (while trying to find specs. on the Sigma 18 Pros), but didn't make the correlation to why that's important. but that totally makes sense. And here I was just trying to prevent low-end sub-sonic rumble from overheating the voicecoils. Incidentally, that's the second time today I saw video of that bridge -- someone is trying to crowd-fund a propless wind powered electric generator and used the same event as part of their promo piece. Much appreciated. So, since the amp has the DSP, and it's not as easy to accidentally change, and that amp will be sticking with these subs for a while, I think I'll move the HPF over to the amp instead of the board. Kinda less chance of accidentally changing (or removing altogether). Still a little uncertain where'd be a good level for the power limiter. I currently have it set to 1200 watts (as I understand, it has only a peak limiter), which is likely a little hot for those drivers. And I suppose, if I bring it down to under 880 (2x440), then I might as well unbridge the thing and not have to worry about special cables, etc. (since each side can deliver 440 watts max into 8 ohms). [/QUOTE]
Insert quotes…
Verification
Post reply
Home
Forums
Pro Audio
Junior Varsity
iNuke nu3000DSP outputs when in bridged mode
Top
Bottom
Sign-up
or
log in
to join the discussion today!