Log in
Register
Home
Forums
New posts
Search forums
What's new
New posts
New profile posts
Latest activity
News
Members
Current visitors
New profile posts
Search profile posts
Features
Log in
Register
Search
Search titles only
By:
Search titles only
By:
New posts
Search forums
Menu
Install the app
Install
Reply to thread
Home
Forums
Low Earth Orbit
DIY Audio
Line Level Isolation Transformers
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Message
<blockquote data-quote="Geoff Doane" data-source="post: 100320" data-attributes="member: 1155"><p>Re: Line Level Isolation Transformers</p><p></p><p>I finally got around to testing the box for crosstalk and external hum pickup.</p><p></p><p>Using the Audio Precision test set, 1kHz crosstalk from CH B into CH A is about -120 dB. That figure was measured with +4 dBu on the B channel, and it improves by a couple dB if the level is increased to +20 dBu, indicating to me that much of that signal is noise, not 1 kHz tone. At the extremes of the audio spectrum, 20 Hz and 20 kHz, the crosstalk increases to -110 dB, so still pretty good. Usually, both inputs are terminated by the generator source impedance (probably about 30Ω), which should keep things quieter on the output under test. Even unplugging the A input to the box from the generator only degraded the crosstalk by about 2 dB (at 1 kHz), so less significant than I might have guessed.</p><p></p><p>As for noise, the measured noise on each channel (22 Hz to 22 kHz band limited) was about -110 dBu. If there's a standard for external magnetic fields, I don't know what it is, so I just used a random wall wart on the end of an extension cord that I could orient in different positions to try to find the worst possible case. The worst I could find induced enough noise in one transformer to measure -53 dBu at the output (inputs terminated by the test set). This was with the top of the wall wart pressed against the side of the ISO box enclosure. At 6 inches away, I could read -80 dBu in certain orientations, and even a foot away, I could still read something above the noise floor, if I turned the wall wart in the right direction.</p><p></p><p>So, it turns out that these transformers are pretty good at containing their own magnetic fields, but not very good at rejecting external fields. </p><p></p><p>I've actually experienced hum pickup into DIs when they got close to wall warts powering keyboards, although I'm not sure about the shielding properties of those DI transformers. I haven't used these ones enough to run into any problems yet.</p><p></p><p>GTD</p></blockquote><p></p>
[QUOTE="Geoff Doane, post: 100320, member: 1155"] Re: Line Level Isolation Transformers I finally got around to testing the box for crosstalk and external hum pickup. Using the Audio Precision test set, 1kHz crosstalk from CH B into CH A is about -120 dB. That figure was measured with +4 dBu on the B channel, and it improves by a couple dB if the level is increased to +20 dBu, indicating to me that much of that signal is noise, not 1 kHz tone. At the extremes of the audio spectrum, 20 Hz and 20 kHz, the crosstalk increases to -110 dB, so still pretty good. Usually, both inputs are terminated by the generator source impedance (probably about 30Ω), which should keep things quieter on the output under test. Even unplugging the A input to the box from the generator only degraded the crosstalk by about 2 dB (at 1 kHz), so less significant than I might have guessed. As for noise, the measured noise on each channel (22 Hz to 22 kHz band limited) was about -110 dBu. If there's a standard for external magnetic fields, I don't know what it is, so I just used a random wall wart on the end of an extension cord that I could orient in different positions to try to find the worst possible case. The worst I could find induced enough noise in one transformer to measure -53 dBu at the output (inputs terminated by the test set). This was with the top of the wall wart pressed against the side of the ISO box enclosure. At 6 inches away, I could read -80 dBu in certain orientations, and even a foot away, I could still read something above the noise floor, if I turned the wall wart in the right direction. So, it turns out that these transformers are pretty good at containing their own magnetic fields, but not very good at rejecting external fields. I've actually experienced hum pickup into DIs when they got close to wall warts powering keyboards, although I'm not sure about the shielding properties of those DI transformers. I haven't used these ones enough to run into any problems yet. GTD [/QUOTE]
Insert quotes…
Verification
Post reply
Home
Forums
Low Earth Orbit
DIY Audio
Line Level Isolation Transformers
Top
Bottom
Sign-up
or
log in
to join the discussion today!