Hi;
I´ve a huge problem.
-X32 Firmware is v1.15. Same problem when it was v1.08.
-I plug 1 X32 and two S16 to the same well grounded socket; same phase for three of them.
-I use 2 Cat5e wires. One goes from AES50 Port A of the X32 to the first S16´s Port A socket.
-The second CAT5e wire goes from first S16´s Port B to second S16´s Port A.
-I set the Syncronization to "Local", and the sample rate to 44,1 KHz. Anyway, I´ve the same problem to 48 KHz.
-I set first S16 to "1-8", and the second one to "9-16".
-I route input channels (32 channels), and start working. Everything is fine.
-I record the Master Buss to a 2GB USB pen drive, formatted to Fat32. Same problem with a 2GB Fat16 pendrive. Same problem too without any pendrive inserted on X32.
-Link of the noise sample: https://www.dropbox.com/s/ad1c8dclm4e2xfe/X32 + 2xS16 Dropout and MASTER NOISE.mp3
PROBLEM:
Suddenly a 0DBFS "click" sounds in the Master buss. At the same time, sound stops. All channel´s "gate" red light (in the channel´s metering red light) switch on, even if the channel was not gated. 8 seconds later a super strange almost full range digital terrible noise (You have a Link with a sample below) increases exponentially reaching 0DBFS in the Master Buss. Doesn´t mind if I mute all channels, or if I do anything else. I can only go down with the Master Fader, and sound decreases acording to fader, but if I raise it keeps on sounding. The only way to stop this situation is shutdown the mixer. Synchro green lights are OK, recalling other scenes doesn´t work.
¿¿¿¿Any clue or solution????
I´ve a huge problem.
-X32 Firmware is v1.15. Same problem when it was v1.08.
-I plug 1 X32 and two S16 to the same well grounded socket; same phase for three of them.
-I use 2 Cat5e wires. One goes from AES50 Port A of the X32 to the first S16´s Port A socket.
-The second CAT5e wire goes from first S16´s Port B to second S16´s Port A.
-I set the Syncronization to "Local", and the sample rate to 44,1 KHz. Anyway, I´ve the same problem to 48 KHz.
-I set first S16 to "1-8", and the second one to "9-16".
-I route input channels (32 channels), and start working. Everything is fine.
-I record the Master Buss to a 2GB USB pen drive, formatted to Fat32. Same problem with a 2GB Fat16 pendrive. Same problem too without any pendrive inserted on X32.
-Link of the noise sample: https://www.dropbox.com/s/ad1c8dclm4e2xfe/X32 + 2xS16 Dropout and MASTER NOISE.mp3
PROBLEM:
Suddenly a 0DBFS "click" sounds in the Master buss. At the same time, sound stops. All channel´s "gate" red light (in the channel´s metering red light) switch on, even if the channel was not gated. 8 seconds later a super strange almost full range digital terrible noise (You have a Link with a sample below) increases exponentially reaching 0DBFS in the Master Buss. Doesn´t mind if I mute all channels, or if I do anything else. I can only go down with the Master Fader, and sound decreases acording to fader, but if I raise it keeps on sounding. The only way to stop this situation is shutdown the mixer. Synchro green lights are OK, recalling other scenes doesn´t work.
¿¿¿¿Any clue or solution????